Planning the Prescribed Burn

Steps to successful prescribed burning - planning

        analysis

        prescription

        preparation

        execution

        evaluation

The first step to a successful prescribed burn is an analysis of forest property and the resource management plan. Determine the needs of each stand and what actions should be taken to meet these needs. Prescribed fire as well as other alternatives should be addressed and a decision reached regarding the preferred treatment.  In many cases prescribed fire is effective as one activity in conjunction with other resource management activities.

Prescription burning is a highly technical job requiring knowledge of weather, fire behavior, suppression techniques, and environmental effects of fire. Analysis should be done well in advance of the burning season by scouting stands that may need a fire treatment and by reviewing the tract/stand history. Over plan the number of acres to be burned by 10 to 25 percent so area substitutions can be made if necessary and so additional areas can be burned if favorable weather continues. The number of days suitable burning in particular fuel models and conditions varies widely from year to year. If you have several blocks to burn, set priorities. Specifically designate any planned burns that require exacting weather conditions. Considerations include heavy fuels, small trees, potential smoke problems (Smoke Sensitive Areas), etc. Indicate all blocks to be burned on an administrative map. When the burns are completed, record the dates on the map.

A burn resource objective should be determined so that a precise prescription including a safety, resource, and fire objective may be established prior to the further development of a burn plan.  Examples of burn resource objective include:

         Site preparation

         Fuel reduction

         Habitat

         Timber stand improvement

         Disease control

         Silva pasture

         Esthetics

         Eco-restoration

        Combinations

A written prescribed-burning plan prepared by a knowledgeable person is needed for each area to be burned. The plan should be completed well before the burning season and preparations made for when the prescribed weather occurs. Some plans may be quite short and simple while others will be complex. Individual blocks can vary from a few acres to over 1,000, but topography and amount and type of fuel in a unit should be similar within a burn block. The plan can consist of a series of blocks in the same compartment or management unit as long as the same objectives apply and the fuel is similar.  No two burns are the same.  Each burn requires a burn plan developed specifically for the conditions in the burn unit.

Large areas should be divided into 1-day burning blocks or smaller areas. Use existing barriers such as roads and creeks as much as possible. Be sure barriers are effective at the time of the burn.

The Written Plan

NO WRITTEN PLAN NO BURN

A unique form including all pertinent information is required for each burn. Develop a unique plan for each burn as part of your annual plan of work. The form should include a checklist to be sure nothing is overlooked.

A prepared form with space for all needed information is best. Complete them as part of your annual plan of work. The form will serve as a checklist to be sure you have not overlooked some aspect or potential impact. Sample forms in PDF format for both understory burns and postharvest burns can be found at the links below. The "simple7 form can be used on small burns within a large landholding that does not contain public roadways. 

These files are in
Adobe PDF Format

Simple Understory Prescribed Burning Unit Plan
Understory Prescribed Burning Unit Plan
Postharvest Prescribed Burning Unit Plan

Contents of the written plan should include:

  • Identification & contact info: owner, planner, burn boss, burn permit date and number
  • Objectives of the burn: resource, fire, SAFETY
  • Location and description of area in detail including timber stand, understory, soils, and terrain; fuel models
  • Range of preferred weather: prescriptive weather with space to include forecast for the day of the burn and actual measurements and observations periodically during the burn
  • Smoke management plan including smoke screening and list of all SSA
  • Ignition plan including season, ignition pattern, ignition technique, time of day, ignition completion, burn out, and mop up completion
  • Holding strategy
  • Contingency plan
  • Complexity review
  • Notification check list and contact info: neighbors, forestry commission county manager, volunteer fire department, sheriff dispatch office
  • Go No GO check list
  • Publicity needs
  • Evaluation of burn
  • Maps showing boundaries and other pertinent information.
TABLE 3. Effects of Age of Rough on some Common fire Parameters
Parameter Age of rough (years)
1 2 4 8 16
Litter fuels (tons/ac) 1.5 - 3 2.5 - 4.5 4 - 7.5 5.5 - 12 6.5 - 15
Fireline intensity    B1
  
(Btu/sec/ft)         H2
8 - 5
30 - 60
12 - 25
50 - 90
20 - 35
80 - 145
25 - 65 30 - 75
Outside Rx underburning window
Flame length          B
   (feet)                   H
0.5 - 1.5
1.5 - 2
1 - 2
2 - 2.5
1.5 - 2.5
2.5 - 3.5
2 -3 2 - 3.5
Outside Rx underburning window
Scorch height3         B
   (feet)                         H
< 5
6 - 10
< 5 - 5
9 - 14
< 5 - 7
13 - 19
5 - 11 6 - 12
Outside Rx underburning window

Assume a 20-year-old southern pine plantation on the Coastal Plain with no understory present. Table values will increase as the amount of understory increases. In the Piedmont and mountains, an understory is likely to have an opposite effect except during severe drought.

1B Backing fire with rate-of-spread of 100 feet per hour and fuel consumption of 60 percent.
2H Heading fire with rate-of-spread of 660 feet per hour and fuel consumption of 40 percent.
3Ambient temperature of 50F and windspeed of 2mph. Lower temperatures and higher windspeeds will decrease scorch height.

Make a prescribed fire plan for each area.

Required Signatures and Dates

Provide spaces for signatures) of person(s) who prepared the plan. This identifies the people who know the most about the plan.

Purpose and Objective(s)

Include in the written plan the reason(s) for prescribing a fire. Examples include: prepare seedbed, control insects or disease, reduce hazard, improve wildlife habitat, control understory, improve forage, increase accessibility, and enhance aesthetics. In addition, give a specific quantifiable objective. State exactly what the fire is to do - what it should kill or consume, how much litter should be left, etc. Also concisely describe the expected fire behavior, including the desired range in flame length. In case prescribed weather conditions do not materialize, this description may allow the objective(s) to still be achieved by varying the firing technique. Such information will also be useful in determining success of a burn. THE MOST IMPORTANT OBJECTIVE OF ANY BURN IS SAFETY!

Map of the Burning Unit

A detailed map of each burning unit is an important part of the burning plan. The map should show the boundaries of the planned burn, adjacent land owners, topography, control lines (both existing and those to construct), anticipated direction of the smoke plume, smoke-sensitive areas, holding details, and other essential information. Plowed control lines may not be necessary where passive breaks are determined to be adequate by the bum manager. Consider expanding the planned burn to employ existing firebreaks and natural barriers. For example, use fuel type boundaries such as occur near creek bottoms where the fire will go out as it encounters fuels with a higher moisture content. Show areas that should be excluded or protected such as improvements, young reproduction, sawdust piles, etc. Subdivide each area to be burned into logical, 1-day burning blocks, or smaller areas if smoke management needs dictate.

Equipment and Personnel

List equipment and personnel needed on site and on standby. Assign duties.

Fire Prescription

The amount of fuel, weather conditions and desired intensity of the burn will determine the firing technique and ignition pattern to use. Species involved and height of overstory will determine the maximum intensity that can be tolerated. Where large amounts of fuel are present, cooler burns can be accomplished by burning when humidity and fuel moisture are near the high end of the range so a smaller fraction of the fuel will burn. Lower temperatures are desirable with more intense fires, especially when understory fuels are tall.

A series of user-friendly computer programs called BEHAVE has been developed to predict the behavior of a fire. They are based on a specific set of fuel data and prescribed weather conditions. These programs will run on a hand-held calculator with a fire behavior CROM (Custom Read Only Memory). You can use them in the field to make instant decisions as burning conditions change.

BEHAVE by Remsoft:  http://remsoft.com/products.php?id=14

BEHAVEPLUS  http://www.fs.fed.us/fire/planning/nist/applicat.htm#BEHAVEPLUS

Always think about smoke management. Make sure your burning plan passes a smoke management  system.   See the section on this web site about SMOKE MANAGEMENT.  NEED LINK HERE TO SMOKE MANAGMENT

Weather Considerations

(Understory Burning)

General Young Stands*

Wind within stand
-Backing
-Heading


1-6 mph
1-4 mph


3-6 mph
(No head fires in young stands)

Relative Humidity

30-55%

40-60%

Temperature 25-60F 25-40F
Fine Fuel Moisture 10-20% 15-25%
|Lower Litter Moist Moist to Slightly Wet
Soil Moist

Damp to Wet

Stability Slightly Unstable Unstable or Slightly Unstable
Mixing Height

1,700-6,500 ft.

Not as Critical

Transport Wind 9-20 mph Not as Critical
Type Fire According to Stand Backing Fire Only.
*
  • Diameter at ground level should be 3" - 5"
  • Bark should be " or thicker
  • Crown should be full and dark green (healthy)
  • Height should be at least 10'
  • Cold temperatures needed
  • Strong and steady winds needed

Conditions may warrant more aggressive ignition as determined by fire behavior on the ground.  Spot/grid ignition can be cool and effective.  Flanking and stripping tend to be hotter.  Care must be taken to manage ignition in consideration of the diurnal cycle taking care to prevent stand damage as the diurnal cycle progresses toward its peak at mid afternoon.

Season

Winter - Most understory burning is done during the winter dormant season. Acceptable relative humidity, temperature, fuel moisture, and steady, persistent winds most often occur then.

Spring - More variable weather and generally higher fire danger dictate smaller burns in the spring. Check with local wildlife specialists to avoid periods when prescribed burning could harm nesting wildlife. Pine buds are more exposed and thus more susceptible to heat damage during elongation.

Summer - Hot weather during the summer means much less heat is needed to raise the temperature of plant tissue to lethal levels. For this reason, summer burns are used to kill undesirable hardwoods - usually a series of burns after an initial winter burn. Care must be taken not to severely scorch overstory crowns. Postharvest burns to dispose of logging debris can be conducted year round, but conditions are especially good in mid to late summer because the high ambient temperatures help dry out the larger materials.

Fall - Exercise special care when burning in early fall just prior to the dormant season. Both loblolly and slash pines are more likely to die if severely scorched or root damaged at this time.

Time of Day

Normally, plan burning operations so the entire job can be completed within a standard workday. Prescribed fires usually are ignited between 10 a.m. and noon after sunshine has evaporated any early morning dew. If an inversion occurred the previous night, wait until daytime heating eliminates it before igniting the fire. If the forecast is for poor nighttime dispersion, halt ground ignition before 3 p.m. standard time (ST). Always halt aerial ignition before 4 p.m. ST, to allow adequate time for the fire to burn out before atmospheric dispersion conditions deteriorate. After dark, the smoke plume that is left will start dropping back toward the ground due to the rapid change to stable conditions.

Burning conditions are usually better during the day than at night. All aspects of weather will be better. Windspeed is higher and wind direction steadier. Smoke management is also much easier during the day. At night smoke tends to stay close to the ground and collect in depressions. Also, relative humidity usually increases at night, resulting in spotty burning and an increased likelihood that fog will form.

However, on winter nights when a strong cold front moves across an area, winds remain strong and persistent and relative humidity does not rise greatly. These conditions can provide good prescribed burning weather, especially when cooler temperatures are needed. Whenever night burning is done, keep a close check on wind, humidity, and smoke drift. Be sure that no SSA's will be impacted.

Firing Plan

Key parts of a successful prescribed burn are plans for firing and holding a burn. This plan should consist of a narrative section and a detailed map. The burning unit map is ideal for this purpose because it already contains much pertinent information. Add the following items:

  • Firing technique, ignition pattern, and planned ignition time.
  • Manpower and equipment needed, and planned distribution for setting, holding, patrolling, and mopping up the fire and managing the smoke.
  • Location and number of reinforcements and equipment that can be mobilized rapidly if fire escapes.
  • Instructions for all supervisory personnel, including complete description or illustration of assignment and forces needed to fire out, hold, and mopup the fire.

Alternative Prescriptions

Consider alternative sets of weather conditions (wind, relative humidity, , and/or fuel moisture) and methods of burning that will produce a fire of about the same intensity and accomplish the desired objectives. Two separate burns may be necessary to eliminate heavy volumes of fuel without damage to the overstory.

Preparation Work and Protection of Sensitive Features

Include fire lines to be constructed, snags to be lined or felled, special features to be protected and the installation of any monitoring equipment. Give instructions for the protection of sensitive areas. Consider historical and archeological sites, streams, habitats of threatened and endangered species, and fragile soils.

Notification of Intent to Burn

List the names and telephone numbers of the local State fire protection officer and other officials who should be contacted prior to the burn. Make direct contact with all homes and businesses in the area likely to be impacted by the burn. Offer to evacuate anyone with respiratory problems during the burn. Put them up in a local motel if necessary. Consider written notification explaining the reasons for the burn and encouraging individuals with respiratory ailments to contact you - include a 24 hour telephone number. Establish responsibility for burn-day contacts and how they will be made. Consider a newspaper article describing the reasons for the burn if you expect to produce lots of smoke or anticipate any negative reactions.

Establish Burn Acreage Goals But NOT Quotas!

Impact of Smoke

List any sensitive areas near to, downwind, or down drainage of the burn. Include smoke management strategies of avoidance, emission reduction, dispersal, or all three, to minimize any adverse smoke impacts. Attach the smoke management plan (e.g. screening system calculations) as part of the burning plan. Smoke Management

If an accident occurs near your burn, be prepared to defend your actions in a lawsuit. (see potential problems)

Legal Requirements

List any legal requirements that might apply, and what the prescribed burner must do to comply. Remember, the person who conducts the prescribed burning operation may not be the one who made the analysis and prepared the prescription. Follow all applicable statutes, regulations, and agency procedures. Needs for a written prescribed burning plan, documentation of deviations from the plan, and good judgment cannot be overemphasized. Erroneous forecasts, unforeseen local influences, and accidents occur despite our best efforts to prevent them. Proper documentation will help establish that the prescribed fire was conducted in a prudent and professional manner. If a prescribed fire results in damage or bodily harm and you cut corners, neglected any mandatory requirements, or acted with disregard to the welfare of others, you are likely to be held responsible, regardless of whether compliance would have changed the outcome. For more information see the summary article, Legal Implications of Prescribed Burning in the South by William C. Seigal, listed in the Suggested Reading section.

Many states have passed a "right to burn act". Be sure all the requirements are met and the burn  boss is certified.

Escaped-Fire Plan

Identify potential fire escapes and specify actions to take should such occur. Designate who will be in charge of suppression action and what personnel and equipment will be available.

Control and Mop up

A plan must include necessary safeguards to confine the fire to the prescribed area and reduce smoke impact. Mopup promptly and completely. Emphasize protection of all adjacent land. Consider and make plans for any variation in forecasted weather that may change a prescribed fire into a damaging wildfire, increase the pollution in smoke-sensitive areas, or create visibility problems on adjacent roads.

Evaluation

Include space for a written evaluation of the prescribed burn. A record of actual weather conditions, behavior of the fire, and total environmental effects of the burn is essential. This information is used to determine the effectiveness of the prescribed burn and in setting criteria for future burns.

At the beginning of the prescribed burn, record windspeed and direction, fuel moisture, humidity, burning index, temperature, days since and amount of last rain, and dampness of soil and lower litter. Also record fire behavior data such as type of fire used, length of flames, and forward rate of spread. Continue to record applicable weather and fire-behavior parameters at 2- to 3-hour intervals throughout the burn. After the burn, record amount of crown scorch, consumption of brush, litter, and duff, and any other evidence of fire intensity such as unburned areas, exposed mineral soil, and cracks in bark or cupping on the lower bole due to bark consumption. Also include a short narrative on success of the burn.

Prescribed Fires Often Behave Erratically At Edges Of Openings

eddies caused by forest opening1.gif (39182 bytes)

convection and eddies1.gif (28731 bytes)

Eddies caused by forest openings

  Convection and eddies for open areas